The
pool interior surface cures 60% in the first 30 days and the balance of
the cure continues for the next 10 to 12 months.
You
will be responsible for brushing the pool/spa surface and balancing the
pool/spa water. The beauty and health of your pool, plaster is dependent
on proper and timely performance of these tasks.
BRUSHING
THE WALLS, FLOORS, STEPS, BENCHES, AND LOVESEATS
The
pool should be brushed two times a day for the first tow weeks,
beginning as the pool is completely filled
with water. We recommend the brushings continue until all loose
material from the curing plaster is removed from the surface. Do not operate the pool cleaner for at least two weeks after your pool is started up because the wheels
will leave track marks on the new
uncured Interior surface. The filtration system should
run 24 hours a day until the
pool water is balanced. Excessive
amounts of loose material on the pool surface may require hand vacuuming
for faster removal. Vacuuming this. Loose material will normally result
in pressure build up in the filter and may need backwashing to clean the
pool filter.
Without
proper brushing, the plaster will develop a rough sandpaper-like texture
and discoloration from standing material, dirt and debris.
BRUSHING
PROCEDURES
NOTE:
You will find during the first two (2) weeks after the pool is
filled, that the pool filter pressure will increase as the plaster dust
is being removed from the pool/spa. This is normal and will require
backwashing of the pool filter. When the filter pressure gets 5# greater
than normal, you will need to backwash your pool filter. (See
backwashing procedures)
A.
Brushing Pool
|
1.
Close both the “nears” and “far”
skimmer valves. |
|
2.
Brush all steps, love seats, swim outs, walls and floor
to the pool main drain. |
|
3.
Re-open the two (2) skimmers “near” and “far”
valves. |
B.
Brushing Spa
NOTE:
As you perform these steps you will notice that the water level of the
spa is going down. This is to be expected.
|
1.
Place the primary suction valve (pool/spa) in spa mode. |
|
2.
Close spa fountain valve to reduce surface movement. |
|
3.
Leave the primary return valve (pool/spa) in pool return. |
|
4.
Brush all steps, walls and floor to the spa main drain. |
|
5.
Place the primary suction valve (pool/spa) in pool mode. |
|
6.
Place the primary return valve (pool/spa) in spa mode. |
|
7.
Open spa fountain valve to the normal position |
|
8.
After spa has re-filled, place the primary return valve
(pool/spa) back in pool mode. |
BACKWASHING
PROCEDURES
NOTE: Always
turn the power to the pool filter pump “off’ prior to moving
the backwash handle either up or down.
|
A.
Turn pool pump ‘off.” |
|
B.
Move backwash handle into the backwash mode. |
|
C.
Turn pool pump ‘on.” |
|
D.
Run for approximately 30-45 seconds. |
|
E.
Turn pool pump “off.” |
|
F.
Move backwash handle back into the filter mode. |
|
G.
Turn pool pump “on.” |
|
H.
Run for approximately 30-45 seconds. |
|
I.
Turn pool pump “off.” |
|
Note:
Repeat steps B. through I., approximately 3 to 4 times. |
|
J.
Move backwash handle into the filter mode. |
|
K.
Turn pool pump “on.” |
|
L.
Recharge pool filter with new “Diatomaceous Earth
(DE)*.” |
|
Note:
*This is extremely important — the DE is your filter
material. |
|
|
1.
Amount of DE to recharge the pool filter with (pool
filter size): |
| a.
48 Sq Ft - 10 - 1 pound coffee cans. |
| b.
60 Sq Ft - 12 - 1 pound coffee cans. |
| c.
72 Sq Ft - 14 - 1 pound coffee cans. |
|
|
2.
Place the DE powder into a five (5) gallon bucket and add
water to make a liquid. |
|
3.
Pour the liquid into the near skimmer. The DE will be
drawn into the pool filter via the skimmer and the pool pump. |
Frequent
backwashing is normal during the first few weeks. Once the plaster has
finished curing, backwashing requirements will return to normal
(provided proper filtration, chemical, and cleaning care is followed).
The filtration system may now be set to operate for normal seasonal and
pool size requirements. The pool cleaner may be installed after the two
(2) week brushing period is completed.
WATER
MAINTENANCE
Your
pool has been treated with an initial chemical treatment consistent with
the chemical requirements for your city water supply. Since the curing
process of the plaster, environmental conditions, number of swimmers,
etc. have an impact on your pool water, it is important that you monitor
your water chemistry daily throughout the first few weeks. Then test it
several times a week thereafter as needed.
You
can use a simple-to-use test kit, which will allow you to test for and
control the pH, chlorine, total alkalinity, and acid demand. These same
tests, plus additional tests for calcium hardness, copper, iron, total
dissolved solids, and free chlorine, can be tested for you at your local
pool retail center.
Note:
This specific area will have the greatest impact on the beauty and
health of your plaster.
[ BACK TO TOP OF PAGE
]
